How to Install a Ghost Immobiliser
A ghost immobiliser is a hidden security system that shields your car from key cloning and hacking. It works by stopping the engine from running until a PIN number is entered. This could be as long as 20 characters.
It is unnoticeable by thieves and they are unlikely to think about this additional layer of security. Some systems also have an application that allows owners to disarm the immobiliser in case they forget their PIN or to switch to the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser is an innovative security system that can be incorporated into your vehicle's ECU and provides a discrete line of defence against thieves. It is highly efficient and user-friendly. immobiliser ghost makes it a valuable asset to your vehicle's security arsenal. However, like any anti-theft system, it is not foolproof and requires regular maintenance to ensure optimal operation. This guide will help you get the most of your Ghost 2 immobiliser.
CAN (Controller Area Network) is a robust serial networking system that lets microcontrollers communicate with each other over short distances. A central control unit is not required. It is designed for multiplexing electrical wiring within vehicles to reduce copper usage and comes with a variety of advantages, including low costs and ease of use.
The CAN protocol is used in most modern vehicles to communicate with the engine management system, transmission controller, steering control module, air conditioning controls, and more. It also carries sensor data including inputs and speed sensors, to control various features of the vehicle. The CAN bus is used to monitor these different components, and can prevent the vehicle from starting if they are in a dangerous state.
It is important to understand how the CAN bus works and how it's secured. It is possible to add additional features to vehicles using CAN bus, however it's important to secure it from hackers and other threats. Installing a firewall, and monitoring your CAN bus with software is the best way to achieve this.
Ghost2's control unit is hidden in the wiring harness or dashboard, removing the possibility of a burglar physically altering it. It is impossible to reset a PIN code or an emergency code without access to the car.
You can activate Transport Mode if you need to give your vehicle away for valet parking, service or for any other reason. This feature will disable the Ghost immobiliser's ignition and keyfob functions, and will only be activated when the car reaches 31 mph for 15 minutes.
Creating an PIN code
The Ghost immobiliser shields your vehicle from thieves. The revolutionary technology utilizes a PIN to shut down the vehicle's engine and prevent it starting without the correct code, or an authorized fob or mobile. The system's sleek design makes it virtually invisible and offers unrivaled security against theft. The system is TASSA certified and could save you substantial amounts on your car insurance.
During installation, Ghost enters a "learning mode" to record the sequence of buttons pressed in order to create unique pin codes. The installer will guide you through activating the system after the pin code has been created. Once activated it will Ghost system will shut down your vehicle's starter motor until a valid PIN has been entered or the vehicle is switched into transport mode. This makes it extremely difficult for thieves or cloners to hack or replicate your starter system.
Installing an Ghost immobiliser is simple however it is essential to follow the specific instructions in the user manual to ensure proper operation. Hand tools are essential in making the perfect connections, and a multimeter can assist in determining the electrical parameters. Insulation tape and heat shrink tubing can protect the exposed wiring Cable tie is essential to keep everything tidy and secure. Test the system on a regular basis to identify any potential problems.
Once the installation is complete, it is important to conduct a final test of the system prior to switching on the ignition of your vehicle. Ghost immobilisers will arm themselves after a period of 3 to 30 seconds depending on the model of your car. The system also comes with a Service/Valet mode that allows you to temporarily remove the system for servicing your vehicle or parking valet.
Ideally, the immobiliser should be placed in a hidden location beneath the steering wheel or dashboard. Use a small piece duct tape or paint on the CAN H and L wires to make them easier to locate when you are testing. The CAN H and L wires should also be connected to an electrical source that can provide continuous 12V. It is also crucial to check the connections again after testing, as misidentifying these wires could cause the system to malfunction.
The system must be activated
A ghost immobiliser stops your car from starting unless you press a series of buttons within the car generally the steering wheel, door panel, or central console. The sequence can be changed by the user if needed. Once activated, the system will not be removed. This is a fantastic option for anyone who wants to secure their vehicle from theft.
The system is designed to be undetectable. This means it isn't detected by modern diagnostics or code-grabbing technologies. It doesn't emit radio frequency either which makes it more difficult for thieves to identify.
If the device is found it will stop the engine from running. It will also sound an alarm to scare the burglar away. The device can be used to monitor the location of a vehicle and assist in the recovery of the vehicle in the event that it has been stolen.
If you're interested in a ghost immobiliser call the experts at Car Specalist Customs to get an estimate and discuss your options. We are fully certified to install a ghost immobiliser to your vehicle and will ensure it is concealed in a hard-to-reach area. We can also provide additional security measures like the wheel lock and kill switch to help keep your car safe from thieves.
Disarming the System
If you own a Ghost immobiliser fitted to your vehicle, it's important to know how to disable it. This will help you in the case that you lock your keys in the car or when your battery fails. The system has a unique PIN code that only you know. It will not start the vehicle without this code. The simplest method to enter the code is to press a set of buttons on your dashboard or steering wheel. This is a lot easier than using a key fob, and prevents others from copying the remote.
Ghost2 is noninvasive, unlike some aftermarket immobilisers which require cutting wires to facilitate installation. It also works with the CAN bus system of your vehicle to function. Its most notable characteristic is that it disables the engine, without affecting normal functions of the vehicle. This makes it difficult for thieves to use signal boosters or duplicate keys to car keys. It does not emit radio frequencies, which means thieves are unable to detect it.
The Ghost system also features a Transport Mode that allows you to temporarily disable the security system in circumstances like transportation or servicing. This feature is useful when you're lending your vehicle to someone else without sharing your PIN code, or if your vehicle requires to be secured when you drive it. To activate Transport Mode, press the service button five times within 2 seconds. The Ghost system will confirm activation with 5 indication signals.
Keep the emergency code inside your vehicle in a secure place. If you happen to discover yourself locked out of your vehicle, you'll be able to call the technician or company that installed the system and they'll provide you with the code. If you cannot reach them, you can always try to contact an authorized dealer, but this will involve verification procedures and may incur additional costs.
This system isn't just useful, but it will also protect your vehicle from theft and lower the cost of insurance. Many insurance companies offer lower monthly premiums, or even financial incentives for installing this anti-theft technology.