How to Install a Ghost Immobiliser
A ghost immobiliser is a hidden security system that protects your car from key cloning and hacking. It prevents the vehicle's engine from starting unless it is started using the PIN code that can be as long as 20 characters.
This additional layer of security is not detectable by thieves who are unlikely to expect it. Some systems have an app that allows the owner to disarm their immobiliser in the event of forgetting their PIN or use service/valet mode.
Connecting the vehicle's CAN Bus to the vehicle's
The Ghost 2 Immobiliser is a cutting-edge security system, can be incorporated directly into the ECU of your vehicle. It provides a discreet barrier against thieves. It is highly efficient and user-friendly and can be a valuable addition to your vehicle's security arsenal. However, like website -theft device, it is not 100% reliable and requires regular maintenance to ensure proper operation. Fortunately, this guide will assist you in getting the most value from your Ghost 2 Immobiliser.
CAN (Controller Area Network), a robust serial networking, allows microcontrollers communicate with each over short distances. A central control unit is not required. It is designed to multiplex electrical wiring in vehicles, thereby saving on copper. It has numerous advantages, such as low cost and easy use.
The CAN protocol is utilized in the majority of modern cars to communicate with the engine management system, steering control module and air conditioning controls and many more. It also relays information from sensors, such as speed sensors and other inputs, in order to control the car's various features. The CAN bus can be used to monitor the status of these different components and could stop the vehicle from starting when it is in a dangerous condition.
It's important to know how the CAN bus operates and how it is secured. It is possible to add additional features to vehicles using CAN bus, however it's crucial to safeguard it from attacks from hackers and other dangers. Installing a firewall and monitoring your CAN-bus with software is the best way to achieve this.
Ghost2's discrete control unit is hidden within the dashboard or wiring harness, preventing thieves from physically tampering with it. It's also impossible to reset the PIN code or emergency code without access to the vehicle.
If you need to give your car away for servicing, valet parking, or any other reason, you can use the Transport Mode. This feature disables the Ghost immobiliser's keyfob and ignition functions, and will only come back on when the car reaches 31 mph for 15 minutes.
How do I create a PIN code
The Ghost immobiliser is an effective security system that protects your vehicle from theft. The innovative technology uses a PIN to disable the vehicle's engine and prevent it from starting without the right code, or a valid fob/mobile. Its discrete design ensures the system is inconspicuous and provides unrivaled security against theft. The system is TASSA-certified and could save you substantial amounts on your car insurance.
During installation, Ghost enters a "learning mode" to record the sequence of buttons that are pressed in order to create unique pin codes. The installer will guide you through activating the system once the pin code is created. Once activated the Ghost system will disable the motor that starts your vehicle until you enter a valid pin or switch the vehicle to transport mode. This makes it difficult for thieves or cloners to hack into or replicate your starter system.
It's easy to set up an easy-to-install Ghost immobiliser, but you must follow the precise instructions provided in the user guide to ensure proper performance. Multimeters and basic hand tools can be used to check electrical values. Insulation tape and heat shrink tubing are a great way to protect exposed wiring, while cable ties are essential for keeping everything tidy and secure. Also, be website to test the system regularly to identify any potential issues and errors.
After the installation is completed it is crucial to make a final test of the system prior to turning on the ignition in your vehicle. Ghost immobilisers are able to rearm themselves after 3 to 30 seconds dependent on the model of your car. The system is also equipped with a Service/Valet mode that allows you to temporarily disable the system to service or valet parking.
Ideally, the immobiliser should be placed in an inconspicuous location under the steering wheel or dashboard. It is recommended to use a small amount of duct tape or paint to mark the CAN H and CAN L wires to ensure that you easily locate the wires during testing. The CAN H and L wires must also be connected to an electrical source that can provide continuous 12V. It is important to check the connections again after testing as incorrect identification of these wires could cause the system malfunction.
The system must be activated
A ghost immobiliser prevents your car from starting until you press a few buttons in the vehicle, usually on the steering wheel or door panel, or the central console. The sequence can be changed by the user if needed. Once the system is activated, it is in no way able to be removed by thieves, making it a good option for anyone looking to safeguard their vehicle from theft.
The system is designed to be undetectable, which means it isn't detected by modern diagnostics or code-grabbing technology. It also doesn't send radio signals, which makes it even difficult for thieves to identify the device.
If the device is detected, it will prevent the engine from running and sound a loud alarm to scare off thieves. The device can be used to track a car's location and help police recover the vehicle in case it is taken.
If you are looking for a ghost immobiliser, contact the experts at Car Specalist Customs to get a quote and discuss your options. We are certified to install ghost immobilisers for your vehicle. We will make sure that it is placed in an area that is difficult to reach. We can also install other security measures, including the kill switch and wheel lock, to ensure your vehicle is secure from theft.
Disarming the System
If you have a Ghost immobiliser fitted to your vehicle, it's vital to know how to disable it. It can be used in the event you forget your keys or your battery is dead. The system uses a unique PIN code that only you know, and the immobiliser will not start your car without entering this code. The simplest method to enter the code is to press a combination of buttons on your dashboard or steering wheel. This is much easier than using a key fob and keeps others from copying the remote.
In contrast to some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and integrates with your vehicle's CAN bus network to function. Its most notable feature is that it shuts off the engine without affecting functions of the vehicle. This makes it very difficult for thieves to use signal boosters or to clone keys for cars. Additionally, it doesn't emit radio frequencies, so thieves aren't able to detect the system.
The Ghost system also features an option called Transport Mode, which allows you to temporarily disable the security system in circumstances like transportation or servicing. This is a great option when you need to lend your vehicle to a person who isn't sharing the PIN number or if you wish to ensure your vehicle is secure while driving it. Press the button five times within 2 seconds to activate Transport Mode. The Ghost system will confirm activation using five indication signals.
Save the emergency code outside your vehicle in a safe location. If you ever find yourself locked out of your car you can contact the technician or company who installed the system, and they will give you the code. If you are unable to reach them then you can try to contact an authorized dealer, but this will involve verification procedures and could result in additional charges.
Apart from the ease of this system, you can depend on it to safeguard your vehicle from theft and cut down on insurance costs. Many insurance companies offer reduced monthly premiums, or even financial incentives to install this anti-theft system.